Farmhouse Console Table

Cut list

Board layout. Each row is one board, cut left to right, with the remainder hatched. Dark lines are saw cuts, about ⅛″ wide.

Build it

1. 
   01

   Cut all the pieces

   Cut every piece on the cut list. Before you start on the 2x6s, sight down each board and save the straightest for the top.

   • A Legs, four at 28½″ from the 4x4
   • B Long aprons, two at 38″
   • C Short aprons, two at 7½″
   • D Shelf rails, two at 7½″
   • E Top boards, three at 47″
   • F Shelf boards, two at 45″

   Watch outAll four legs must be exactly the same length or the table will rock. Clamp them side by side and check that the ends line up.
2. 
   02

   Drill the pocket holes

   Set your jig for 1½″ material. Drill on the inside faces only, so no holes show on the finished piece:

   • B long aprons: 2 at each end, plus 4 along the top edge for attaching the top
   • C short aprons: 2 at each end, plus 1 along the top edge
   • D shelf rails: 2 at each end
   • E top boards: 5 along one edge of two boards, starting about 4″ from each end. The last board needs none.

   TipMark the inside face of every piece with a big pencil X before you drill. It's easy to drill a show face by mistake.
3. 
   03

   Build the two leg ends

   Lay two legs (A) on the bench. Fit a short apron (C) between them at the top, flush with the tops and the outside faces of the legs, pocket holes facing in. Glue and drive 2½″ pocket screws.

   Fit a shelf rail (D) between the same legs with its bottom edge 4″ up from the bottom of the legs, flush with the outside faces. Then build the second end to match.

   TipCut a 4″ scrap block and stand the rail on it while you screw. Both ends come out identical.
4. 
   04

   Connect the ends with the long aprons

   Stand both ends up. Fit the long aprons (B) between them at the top, flush with the tops and outside faces, pocket holes facing in. Glue and screw.

   Measure the base corner to corner both ways. When the two diagonals match, it's square. Push on the long corners to adjust before the glue sets.

5. 
   05

   Add the shelf boards

   Lay the two shelf boards (F) on the shelf rails, between the legs, with a ½″ gap between them. Keep the ends flush with the outside of the rails.

   Pre-drill and drive two 2½″ wood screws through each end of each board into the rails.

6. 
   06

   Join the top boards

   Lay the three top boards (E) face down with the pocket holes along the joints. Line up the ends, clamp the boards flat, glue the edges and drive the screws. Work from the middle out.

   Watch outClamp across each joint right at the screw you're driving so the faces stay flush. A step between boards means a lot of extra sanding.
7. 
   07

   Attach the top

   Lay the top (E) face down on a blanket. Center the base upside down on it, with 1″ of overhang on every side. Drive 2½″ pocket screws through the apron holes into the top.

   TipDon't glue the top to the base. Solid wood moves a little with the seasons, and screws alone let it.
8. 
   08

   Sand and finish

   Sand with 80 grit to flatten the top joints, then 120, then 180. Soften the sharp edges with a few passes of sandpaper.

   Wipe off the dust. Stain if you want color, then brush or wipe on two or three coats of a clear topcoat, sanding lightly with 220 between coats.

   TipA console is tall and narrow. In a busy hallway or a home with kids, add a furniture anti-tip strap from the back apron to a wall stud.