Hairpin-Leg Plant Stand
A low plant stand that lifts a big floor pot 13½″ off the floor: one square of 2x12 and four short hairpin legs.
- Skill
- Level 1 of 5 · Beginner
- Build time
- 1 to 2 hours, plus finish
- Lumber
- 1 2x12
- Joinery
- Leg screws
- Finished size
- 11¼″ W × 11¼″ D × 13½″ H
What you need
A 2x12 is actually 1½″ × 11¼″. Every measurement in this plan uses the real size.
Shopping list
- 12x12, 8 ftOne board makes several tops. Pick a flat one.
- 1 set12″ hairpin legs, set of 4Plates no bigger than 4″ square.
- ~20#10 × 1″ pan-head screwsFor the leg plates, if your legs don't come with screws.
- —Sandpaper, 80, 120 and 180 grit
- 1PolyurethaneOr exterior oil.
Tools
- Miter saw or circular saw
- Drill/driverWith a ⅛″ bit for pilot holes.
- Random orbit sander
- Speed square, tape measure, pencil
Cut list
One pieces from one board. Label each piece with its letter in pencil as you cut it.
| Part | Qty | Size, inches | From |
|---|---|---|---|
| ATop | 1 | 1½ × 11¼ × 11¼ | 2x12 |
Board layout. Each row is one board, cut left to right, with the remainder hatched. Dark lines are saw cuts, about ⅛″ wide.
Hardware & tools
Everything besides the lumber, with a link for each.
Links go to Amazon. Woodable earns a small commission at no cost to you.
Required part
12″ hairpin legs (set of 4)The plan is drawn for 12″ legs. Check your legs' instructions for the screw holes before drilling.1 set of 4View on Amazon
Fasteners
- #10 × 1″ pan-head screwsFor the leg plates, if your legs don't come with screws.~20View on Amazon
Glue & finish
- Sandpaper, 80, 120 and 180 grit5″ hook-and-loop discs for a random orbit sander, 80 to 220 grit.View on Amazon
- PolyurethaneOr exterior oil.1View on Amazon
Tools
- Miter saw or circular saw10″ compound miter saw: square, angled and beveled crosscuts.View on Amazon
- Drill/driverWith a ⅛″ bit for pilot holes.View on Amazon
- Random orbit sander5″ random orbit sander.View on Amazon
- Speed square7″ rafter square for marking and guiding cuts.View on Amazon
- Tape measure25 ft tape measure.View on Amazon
Build it
Four steps. The 3D view follows along as you scroll. The parts you're working on are yellow, and the pocket holes or screws for that step are red.
- 01
Cut the top
Square one end of the 2x12, then cut the top (A):
- A Top, one at 11¼″
Check it's square: measure both diagonals. Cut more tops from the same board while the saw is set up.
- 02
Sand and seal the top
Sand the top (A) with 80, 120 and 180 grit and round every edge and corner. Seal all six faces with two or three coats of polyurethane or exterior oil: pots drip and saucers sweat.
- 03
Screw on the hairpin legs
Lay the top (A) face down. Set a hairpin leg in each corner with its plate ¼″ in from both edges, the rods leaning out toward the corner. Mark the holes, drill ⅛″ pilot holes no deeper than ¾″, and drive a #10 × 1″ pan-head screw in every hole.
Check your legs' own instructions first. The plan is drawn for 12″ legs with plates no bigger than 4″ square; bigger plates won't fit four to a top this size.
- 04
Set it up
Stand it up and press on the foot caps. Always use a saucer under the pot, and keep the stand on a flat floor: it's built for one big pot, up to about 14″ across.
Build at your own risk. Check every measurement against your own lumber before you cut, test-fit before you glue, and wear eye and ear protection. Full disclaimer.
